Systemd is complaining that it can't delay the startup of device units.
We have a before dependency on the respective device unit for every
netdev service, which doesn't make any sense because we create the
actual interface in this service.
Previously, depending on the environment and the type of interface that
was created, the configured IPs of an interface wouldn't be applied on a
nixos-rebuild switch. It works after a reboot.
This patch ensures that the network-addresses service is started
either via the network-link service or if the networking target is
activated (i.e. on system activation).
Fixes#28474#16230.
This reverts commit 670b4e29adc16e0a29aa5b4c126703dcca56aeb6. The change
added in this commit was controversial when it was originally suggested
in https://github.com/NixOS/nixpkgs/pull/29205. Then that PR was closed
and a new one opened, https://github.com/NixOS/nixpkgs/pull/29503,
effectively circumventing the review process. I don't agree with this
modification. Adding an option 'resolveLocalQueries' to tell the locally
running name server that it should resolve local DNS queries feels
outright nuts. I agree that the current state is unsatisfactory and that
it should be improved, but this is not the right way.
(cherry picked from commit 23a021d12e8f939cd0bfddb1c7adeb125028c1e3)
This includes fuse-common (fusePackages.fuse_3.common) as recommended by
upstream. But while fuse(2) and fuse3 would normally depend on
fuse-common we can't do that in nixpkgs while fuse-common is just
another output from the fuse3 multiple-output derivation (i.e. this
would result in a circular dependency). To avoid building fuse3 twice I
decided it would be best to copy the shared files (i.e. the ones
provided by fuse(2) and fuse3) from fuse-common to fuse (version 2) and
avoid collision warnings by defining priorities. Now it should be
possible to install an arbitrary combination of "fuse", "fuse3", and
"fuse-common" without getting any collision warnings. The end result
should be the same and all changes should be backwards compatible
(assuming that mount.fuse from fuse3 is backwards compatible as stated
by upstream [0] - if not this might break some /etc/fstab definitions
but that should be very unlikely).
My tests with sshfs (version 2 and 3) didn't show any problems.
See #28409 for some additional information.
[0]: https://github.com/libfuse/libfuse/releases/tag/fuse-3.0.0
Currently the `rpc-gssd.service` has a `ConditionPathExists` clause that can
never be met, because it's looking for stateful data inside `/nix/store`.
`auth-rpcgss-module.service` also only starts if this file exists.
FixesNixOS/nixpkgs#29509.
When the user specifies the networking.nameservers setting in the
configuration file, it must take precedence over automatically
derived settings.
The culprit was services.bind that made the resolver set to
127.0.0.1 and ignore the nameserver setting.
This patch adds a flag to services.bind to override the nameserver
to localhost. It defaults to true. Setting this to false prevents the
service.bind and dnsmasq.resolveLocalQueries settings from
overriding the users' settings.
Also, when the user specifies a domain to search, it must be set in
the resolver configuration, even if the user does not specify any
nameservers.
(cherry picked from commit 670b4e29adc16e0a29aa5b4c126703dcca56aeb6)
This commit was accidentally merged to 17.09 but was intended for
master. This is the cherry-pick to master.
Previously services depending on network-online.target would wait until
dhcpcd times out if it was enabled and a static network address
configuration was used. Setting the default gateway statically is enough
for the networking to be considered online.
This also adjusts the relevant networking tests to wait for
network-online.target instead of just network.target.
Boot fails when a keyfile is configured for all encrypted filesystems
and no other luks devices are configured. This is because luks support is only
enabled in the initrd, when boot.initrd.luks.devices has entries. When a
fileystem has a keyfile configured though, it is setup by a custom
command, not by boot.initrd.luks.
This commit adds an internal config flag to enable luks support in the
initrd file, even if there are no luks devices configured.
Adds /dev/disk/by-{id,label}/* symlinks for bcache device nodes, in the
final rootfs.
Symlinks will only be created for bcache devices that contain
filesystems. So if you have a blank bcache device or run LVM on top of
bcache you will not get this kind of symlink.
This reduces the time window during which IP addresses are gone during
switch-to-configuration. A complication is that with stopIfChanged =
true, preStop would try to delete the *new* IP addresses rather than
the old one (since the preStop script now runs after the switch to the
new configuration). So we now record the actually configured addresses
in /run/nixos/network/addresses/<interface>. This is more robust in
any case.
Issue https://github.com/NixOS/nixops/issues/640.
And adopt the tests to add an interface and remove it again.
It should work when deactivating rstp, it will not work when activating
rstp for the first bridge as then the userspace daemon is not yet
available. But once one bridge is active with stp, it should work with
the reload for any further bridge.
Fixes#21745. Also see #22547.
After the change of the bonding options, the examples were not quite correct.
The diff is over-the top because the new `let` needs everything indented.
Also add a small docstring to the `networkd` attr in the networking test.
reason: after the upgrade of iputils from 20151218 to 20161105
functionality of ping6 and tracepath6 was merged into ping and tracepath.
Ping is now mostly a drop-in replacment for ping6, except that selecting a
specific interface is done by encoding it into the address (ex.: fe80::1%eth0)
rather then specifing it with the `-I` flag.
Since the bonds interface changed to a lot more possible values we create a
mapping of kernel bond attribute names and values to networkd attributes.
Those match for the most part, but have to transformed slightly.
There is also an assert that unknown options won’t slip through silently.
Until now the four attributes available very selectively provided a small
subset, while copying upstream documentation.
We make driver options an arbitrary key-value set and point to kernel
documentation, which is always up-to-date. This way every option can be set.
The four already existing options are deprecated with a warning.
