The previous tentative to the fix got the order mixed up a bit. This
new fix has been re-verified to get them in the good order as per the
instructions in the following chapters.
The tests in <nixos/tests/installer.nix> are using `parted`, so they are
bound to be better tested than `fdisk`.
This is brought on by a couple issues, plus reports on IRC that the
`fdisk` instructions didn't work as expected.
* #39354
* #46309
* #39942
* #45478
Care was taken so that the other documented steps did not need changes.
In all this kerfufle, a slight re-organization of the Chapter has been
made, allowing better deep linking.
While it seemingly brings more attention to the macOS notes with the
default docbook template, it better represents which parts of the
section are about macOS, and which parts are simply in the flow of the
text; otherwise the last paragraph may be lost into the details for
macOS.
The instructions to install nixos behind a proxy were not clear. While
one could guess that setting http_proxy variables can get the install
rolling, one could end up with an installed system where the proxy
settings for the nix-daemon are not configured.
This commit updates the documentation with
1. steps to install behind a proxy
2. configure the global proxy settings so that nix-daemon can access
internet.
3. Pointers to use nesting.clone in case one has to use different proxy
settings on different networks.
* improve nix installation instructions
in the command
$ bash <(curl https://nixos.org/nix/install)
<(..) is a bashism. The documentation now show a command that does
not require to be executed by bash.
- mkfs.fat needs `-n` to set a partition label, not `-L`.
- create /mnt/boot before mounting
- leave out detailed LVM example as advanced users already how to create
LVs while it is detracting for novices.
Re #38674
New thin laptops don't have an ethernet port and so rely on wifi to get
access. With the minimal installer, setup wpa_supplicant can be hard if
it is the first time so here we provide an example.
"Ejecting" from the Finder ejects the entire device which is then not available for dd. diskutil unmountDisk does the right thing. Furthermore writing to diskN instead of rdiskN failed to complete even after waiting >10 minutes.
Also unifies the BIOS and UEFI installation instructions.
It's a fairly basic usage, but it makes explicity the fact that
you should at least have a main partition and a swap partition,
and will save some users a bit of internet searching while they
are getting set up.
... because `nixos-generate-config` currently understand it's running under virtualbox, and correctly adds the configuration in `/etc/nixos/hardware-configuration.nix`
Add link to "Configuration" chapter from "Changing the Configuration" section.
Also, fix grammar error.
(cherry picked from commit a585f987fa32f2e81b3f273291971151c25f98b7)
The tag wasn't properly closed which caused the manual build to fail.
Tested with: nix-build nixos/release.nix -A manual.x86_64-linux
Signed-off-by: aszlig <aszlig@redmoonstudios.org>
* manual: Mark commands that require root
Mark every command that requires to be run as root by prefixing them
with '#' instead of '$'.
* manual: Add note about commands that require root
At some point we probably want to replace this with a curated list
of configurations or even an upstreamed repository of examples, but
for now this is just noise.
FixesNixOS/nixpkgs#14522
Unetbootin works by altering the image and placing a boot loader on it.
For this reason, it cannot work with UEFI and the installation guides
for other distributions (incl. Debian and Fedora) recommend against
using it.
Since dd writes the image verbatim to the drive, and not just the files,
it is not necessary to change the label after using it for UEFI
installations.
vcunat: tiny changes to the PR. Close#14139.
Commit 159fed47bc (nixos/grub: Fix video display on efi) changed BIOS
systems to start in non-text mode as well. Enable FB_VESA to get a
framebuffer console on BIOS systems. Change FRAMEBUFFER_CONSOLE to 'y'
instead of the default 'm' to so the user doesn't need to manually load
the fbcon module anymore.
Other distros have similar defaults, at least on Arch:
CONFIG_FB_VESA=y
CONFIG_FRAMEBUFFER_CONSOLE=y
and on Ubuntu (12.04):
CONFIG_FB_VESA=m
CONFIG_FRAMEBUFFER_CONSOLE=y
Fixes#8139
