Referencing modulesPath in NixOS configurations can cause evaluation
errors in restricted mode. If used as `${modulesPath}` (as in all
use-sites in nixpkgs) the modules subtree is copied into its own store
path. Access to this path will be forbidden in restricted mode.
Converting to a string solves this issue.
`${builtins.toString modulesPath}` will point to a subdirectory of the
nixpkgs tree out of which evalModules is called.
This change converts modulesPath to a string by default so that the
call-site doesn't have to anymore.
Take two of #40708 (4fe2898608).
That PR attempted to bidirectionally default `config.nixpkgs.system` and
`config.nixpkgs.localSystem.system` to each be updated by the other. But
this is not possible with the way the module system works. Divergence in
certain cases in inevitable.
This PR is more conservative and just has `system` default `localSystem`
and `localSystem` make the final call as-is. This solves a number of
issues.
- `localSystem` completely overrides `system`, just like with nixpkgs
proper. There is no need to specify `localSystem.system` to clobber the
old system.
- `config.nixpkgs.localSystem` is exactly what is passed to nixpkgs. No
spooky steps.
- `config.nixpkgs.localSystem` is elaborated just as nixpkgs would so
that all attributes are available, not just the ones the user
specified.
The remaining issue is just that `config.nixpkgs.system` doesn't update
based on `config.nixpkgs.localSystem.system`. It should never be
referred to lest it is a bogus stale value because
`config.nixpkgs.localSystem` overwrites it.
Fixes#46320
toPath has confusing semantics and is never necessary; it can always
either just be omitted or replaced by pre-concatenating `/.`. It has
been marked as "!!! obsolete?" for more than 10 years in a C++
comment, hopefully removing it will let us properly deprecate and,
eventually, remove it.
I ended up with a corrupted image with the debugfs contraption once, and
given I couldn't reproduce the problem I suppose that happens if the
filesystem of the builder runs out of space.
At least in this instance fsck could detect it, so let's add it as a
sanity check.
The ability to specify "-drive if=scsi" has been removed in QEMU version
2.12 (introduced in 3e3b39f173).
Quote from https://wiki.qemu.org/ChangeLog/2.12#Incompatible_changes:
> The deprecated way of configuring SCSI devices with "-drive if=scsi"
> on x86 has been removed. Use an appropriate SCSI controller together
> "-device scsi-hd" or "-device scsi-cd" and a corresponding "-blockdev"
> parameter instead.
So whenever the diskInterface is "scsi" we use the new way to specify
the drive and fall back to the deprecated way for the time being. The
reason why I'm not using the new way for "virtio" and "ide" as well is
because there is no simple generic way anymore to specify these.
This also turns the type of the virtualisation.qemu.diskInterface option
to be an enum, so the user knows which values are allowed but we can
also make sure the right value is provided to prevent typos.
I've tested this against a few non-disk-related NixOS VM tests but also
the installer.grub1 test (because it uses "ide" as its drive interface),
the installer.simple test (just to be sure it still works with
"virtio") and all the tests in nixos/tests/boot.nix.
In order to be able to run the grub1 test I had to go back to
8b1cf100cd (which is a known commit where
that test still works) and apply the QEMU update and this very commit,
because right now the test is broken.
Apart from the tests here in nixpkgs, I also ran another[1] test in
another repository which uses the "scsi" disk interface as well (in
comparison to most of the installer tests, this one actually failed
prior to this commit).
All of them now succeed.
[1]: 9b5a119972/tests/system/kernel/bfq.nix
Signed-off-by: aszlig <aszlig@nix.build>
Cc: @edostra, @grahamc, @dezgeg, @abbradar, @ts468
Following legacy packing conventions, `isArm` was defined just for
32-bit ARM instruction set. This is confusing to non packagers though,
because Aarch64 is an ARM instruction set.
The official ARM overview for ARMv8[1] is surprisingly not confusing,
given the overall state of affairs for ARM naming conventions, and
offers us a solution. It divides the nomenclature into three levels:
```
ISA: ARMv8 {-A, -R, -M}
/ \
Mode: Aarch32 Aarch64
| / \
Encoding: A64 A32 T32
```
At the top is the overall v8 instruction set archicture. Second are the
two modes, defined by bitwidth but differing in other semantics too, and
buttom are the encodings, (hopefully?) isomorphic if they encode the
same mode.
The 32 bit encodings are mostly backwards compatible with previous
non-Thumb and Thumb encodings, and if so we can pun the mode names to
instead mean "sets of compatable or isomorphic encodings", and then
voilà we have nice names for 32-bit and 64-bit arm instruction sets
which do not use the word ARM so as to not confused either laymen or
experienced ARM packages.
[1]: https://developer.arm.com/products/architecture/a-profile
exportReferencesGraph is deprecated and doesn't have the generated
initial Nix database contain the SHA256 of the contents of the store
paths, which breaks various things under Nix 2.0.
- `localSystem` is added, it strictly supercedes system
- `crossSystem`'s description mentions `localSystem` (and vice versa).
- No more weird special casing I don't even understand
TEMP
Instead of imagemagick built with many libraries
(notably librsvg which these days requires rust)
use imagemagick_light with support for libtiff added.
These (outdated) derivations are only used by nixos/lib/testing.nix.
If we want to provide jquery & jquery-ui packages this is better done
in nodePackages.
Among other things, this will allow *2nix tools to output plain data
while still being composable with the traditional
callPackage/.override interfaces.
- Add a new parameter `imageType` that can specify either "efi" or
"legacy" (the default which should see no change in behaviour by
this patch).
- EFI images get a GPT partition table (instead of msdos) with a
mandatory ESP partition (so we add an assert that `partitioned`
is true).
- Use the partx tool from util-linux to determine exact start + size
of the root partition. This is required because GPT stores a secondary
partition table at the end of the disk, so we can't just have
mkfs.ext4 create the filesystem until the end of the disk.
- (Unrelated to any EFI changes) Since we're depending on the
`-E offset=X` option to mkfs which is only supported by e2fsprogs,
disallow any attempts of creating partitioned disk images where
the root filesystem is not ext4.
